Robin Hoods Playground

Well as I stated this is a TEST, Like most people I do not have $1,000+ to do it with a reball station. This is the stencil I will be picking up, local shop has one they will sell me. http://cgi.ebay.com/XBOX360-CPU-GPU-XSB-CACHE-HANA-BGA-Reball-Station-kits-/280583216390?pt=LH_DefaultDomain_0&h...

Alright, I'm going to take a lot of picture's once I order the reball die. So far I've freaked coffee out showing him proof of concept with the ps2 board, I've almost desoldered the entire thing now. From the experience I have so far you defiantly want something to monitor the chip for heat (I am li...

Hey guys, figured I'd say hi and tell you what SGTCOFFEE and I are up to. This is more my idea but... We have a few red ringed xbox's that we fixed with a heat gun and are now failing. Now I'm practicing with said heat gun at taking old BGA chips off of some ps2's to get a feel for it before decidin...

what I mean by set it up is like.. Install it and it be the one thing that boots. Instead of having to load it through the games section. Most videos i have seen, everyone goes to their game folder and it shows as a game demo... Then they load into it.. I was thinking more of going straight to the n...

@Haggard, Unleashed sound right.. Is there a way to set up a dashboard like that? I think I'll go dig out my cds with my nes games lol, gotta revisit the classics! @Cofree, Is there a way to make these more permanent? Most of these had been xclamped, the e74's and the dead board weren't.. But I went...

Gosh, I don't know what I'm going to do with you guys. I Have five xbox's laying around my house now because of Cofree and Haggard. And to think.. This time last week I did not have a single working Xbox. Just want to say thanks, You guys helped me jtag a console, and spoof a drive into it to get it...

Thanks haggard and Cofree!! Got this box working! Had a little trouble at first following haggards guide here.. then i remembered this drive i have was a 79 LOL and finally got my unlock disk out. Works like a charm when you do things right!

Hey guys, Just thought I would update yall on the happenings. Successfully got my drive key from the vault using the jtag! And then spoofed a new drive to this on! Thanks for the help and input!

OK, having some small problems. When i flashed back to my original dump.. the box turns on and the middle light is on. But i dont get the safe spinning green light and boot up. Just sits there. Do i need to erase my nand? or should i just short it out and see if that brings it back? Open to ideas he...

Hey guys, i just got through recovering the drivekey of an xbox that im trying to salvage with my dad. After install xell and getting the drive key and the drive type we discovered that the original drive was an HL-DT-STDVD-ROM GDR3120L0059... Thats the drive WE DO NOT HAVE. So i do not have a firmw...

OK! Got xell to boot. had to use this diagram ..... Then had to use 360 flash tool dump .98, Thanks for the help!

Alright, well im about to swap out the switching diodes on the three jtag points for the 330 ohm resistors like i saw in the original version of the jtag for xenon. Will update afterward. Im sure my jtag connections are good cause i can reflash my nand with the original and it turns on but wont boot...

Need some help, just installed xell and tried to boot up to get the white\blue screen.. and got an e79. currently going to my orig dump. Any help? If you have yahoo and could\would like to help add me.... boomtownxcs at yahoo dot com or just leave a comment here pointing me in a direction. just fini...

Alright, well i guess my next step is to put on the last 3 points before i write the xell. right?

Hello fellow nottinghamians!(*spelling?*) My father and I recently came across a broken down xbox 360, the drive has completely been fried. We decided to jtag it and get the dvd key and spoof it. So far we have dumped the nand four times. This is xenon mobo withuot HDMI, CB of 1903. On the four dump...