Robin Hoods Playground

The 93450c generates "Lite-OFW.bin"

I have not seen a dummy file. I read somewhere that "Lite-OFW.bin" is technically a larger file that contains what dummy and other files you see, but as one larger file.

Deathuntou, the dumped file that I have is just "Lite-OFW.bin" - which I assume is all you need. I can't recall, but when doing this, I do not need to read things again, nor unsolder. From the sound of it, all I need is to connect the drive to the PCI card, and with JungleFlasher perform a...

A while ago I have successfully flashed a Liteon 93450c drive to iXtreme LT Lite Touch 1.7 using JungleFlasher. I have used Xtractor Maximus, Vampire (a probe) and a Rebuild Board. The process involved cutting and soldering. The original drive firmware (Lite-OFW.bin) is what I have extracted. Right ...

You mean, to revert to OFW from CFW (for dashboard updates, etc), one would have to recut things... I am not sure about that... a board is there in place, the cuts were already done - this was all done for the purpose of getting the OFW file. The purpose of cutting, and soldering things was to get t...

Just load the ofw as target and source, then flash that. This with JungleFlasher? Once loaded in these areas, what then? Why does this file have to be BOTH in target and source? Does not make sense, what are you loading from TARGET into SOURCE when the file is the same...? Then under "MTK Flas...

I think that is all you need dude - the bin file only. I am in a similar situation. I think we need to load the Lite-OFW.bin into source to go back to original firmware. Not sure on what buttons needed to be clicked with JungleFlasher to perform that... The only file that was extracted from the driv...

I went with this option: Xtractor 1.1, Vampire, and a rebuild board. It is not too tough. Follow their tutorial for the cutting, installation and then use JungleFlasher tutorial to read the drive. I am a newbie to this, but got it working. I had problems with getting the VIA card finding the port to...

I have successfully flashed a Liteon 93450c drive to iXtreme LT Lite Touch 1.7 using JungleFlasher. I have used Xtractor Maximus, Vampire (a probe) and a Rebuild Board. The process involved cutting and soldering. The original drive firmware (Lite-OFW.bin) is safe. I do have a number of questions, th...

Quick questions in regards to this. I have flashed my Liteon to the latest LT 1.1 Not sure what is needed to go to original firmware, then back again to LT1.1 using the extracted Lite-OFW.bin file. The only file that was extracted from the drive was Lite-OFW.bin - this is all I need to reflash back ...

Make sure the light on the switch is green when reading. You should power it on in normal mode, then click intro, dont click yes yet, then turn off your ck3, flip the switch then hit yes, then power it on, then flip the switch back over so its now green then hit read. That should fix your read erro...

Thank you - will try that. Anyone know if similar procedure is to be done with other tools? (ie. Xtractor with Vampire)? Thank you.

Have purchased Xtractor, Vampire and rebuild board for a Liteon 93450C drive. Soldered and tested all points on the soldered rebuild board using a multimeter (set to Omega at 20K reading). S1A to S1B - current flowing (circuit is closed) S1A to S1D - current flowing S1A to S1C - current flowing S1A ...

sorted it now poeple , i read through the instructions again and realised i was doing it slightly wrong :lol: done it now my first 934 up and running ;) thanks for the help shaky - can you please post what you did to make it work... I am running into the same issue with a Liteon 9345C after I press...