JTAG Nand dump help

Only things pertaining to J-Tag
Forum rules
Only post or question about doing J-tag on a 360.
All other post/question will be moved or trashed.
Post Reply
Boomtown
Peasant
Peasant
Posts: 17
Joined: Thu Dec 27, 2007 2:35 am

JTAG Nand dump help

Post by Boomtown »

Hello fellow nottinghamians!(*spelling?*) My father and I recently came across a broken down xbox 360, the drive has completely been fried. We decided to jtag it and get the dvd key and spoof it. So far we have dumped the nand four times. This is xenon mobo withuot HDMI, CB of 1903. On the four dumps, NANDpro does not give me any errors, upon comparing the dumps I have 33 non matching blocks. Im comparing these dumps with JTAG Tool by coolshrimp. I have used Degraded to check the individual dumps and it shows now errors. Are we in the clear to move on? Or do we need to dump some more. Or patch the bin with nandcompare 3.1?

Help is much appreciated! Boomtown and SGTCOFFEE
User avatar
MrMiscellaneous
Bandit
Bandit
Posts: 76
Joined: Sun Feb 01, 2009 11:46 am

Re: JTAG Nand dump help

Post by MrMiscellaneous »

I believe you are pretty much done with checking all of the data. Next is to re-flash your nand with XeLL and get your cpu key so you can get even closer :P
Image
Boomtown
Peasant
Peasant
Posts: 17
Joined: Thu Dec 27, 2007 2:35 am

Re: JTAG Nand dump help

Post by Boomtown »

Alright, well i guess my next step is to put on the last 3 points before i write the xell. right?
Boomtown
Peasant
Peasant
Posts: 17
Joined: Thu Dec 27, 2007 2:35 am

Re: JTAG Nand dump help

Post by Boomtown »

Need some help, just installed xell and tried to boot up to get the white\blue screen.. and got an e79. currently going to my orig dump. Any help? If you have yahoo and could\would like to help add me.... boomtownxcs at yahoo dot com or just leave a comment here pointing me in a direction. just finished checking my solder points and they look good. Im the two switching diode method on a xenon mobo. Did i miss a step?
User avatar
MrMiscellaneous
Bandit
Bandit
Posts: 76
Joined: Sun Feb 01, 2009 11:46 am

Re: JTAG Nand dump help

Post by MrMiscellaneous »

I'm pretty sure haggardsmurf would know about that. I believe others have gotten that error but i wouldnt know. I'd try this guide http://www.se7ensins.com/forums/topic/1 ... -nandxell/ (although doesnt show how to install other stuff after you jtag it;you could look it up on youtube or somewhere else) Still havent gotten my hands on a jtag-able board but have studied it enough.
Image
User avatar
HaGGardSmurf
Ally of Robinhood
Ally of Robinhood
Posts: 4088
Joined: Tue Feb 03, 2009 9:46 am
Location: Alberta, Canada

Re: JTAG Nand dump help

Post by HaGGardSmurf »

I've never jtagged, but from what I know if you get e79 after flashing xell, you have a bad connection somewhere, or using wrong/bad resistors. (Or correct resistor in the wrong spot)

If you boot your console and the jtag fail's (bad connection somewhere, and the data does not get to the cpu/gpu) then your console will look for the dashboard, and fail giving you e79.

Make sure your resistors are in the right location, and make sure all your joint's are good. When you solder, you should be heating the solder point, and the solder, not just the solder, then dabbing the solder onto the point.
Boomtown
Peasant
Peasant
Posts: 17
Joined: Thu Dec 27, 2007 2:35 am

Re: JTAG Nand dump help

Post by Boomtown »

Alright, well im about to swap out the switching diodes on the three jtag points for the 330 ohm resistors like i saw in the original version of the jtag for xenon. Will update afterward. Im sure my jtag connections are good cause i can reflash my nand with the original and it turns on but wont boot into the systems orig menu. From what i read if you have the jtag soldering right it will turn on but not actually boot. I get no e79 when its in the original dump. Be back soon!
Boomtown
Peasant
Peasant
Posts: 17
Joined: Thu Dec 27, 2007 2:35 am

Re: JTAG Nand dump help

Post by Boomtown »

OK! Got xell to boot. had to use this diagram Image..... Then had to use 360 flash tool dump .98, Thanks for the help!
Boomtown
Peasant
Peasant
Posts: 17
Joined: Thu Dec 27, 2007 2:35 am

Re: JTAG Nand dump help

Post by Boomtown »

OK, having some small problems. When i flashed back to my original dump.. the box turns on and the middle light is on. But i dont get the safe spinning green light and boot up. Just sits there. Do i need to erase my nand? or should i just short it out and see if that brings it back? Open to ideas here :)
Boomtown
Peasant
Peasant
Posts: 17
Joined: Thu Dec 27, 2007 2:35 am

Re: JTAG Nand dump help

Post by Boomtown »

Hey guys, Just thought I would update yall on the happenings. Successfully got my drive key from the vault using the jtag! And then spoofed a new drive to this on! Thanks for the help and input!
User avatar
MrMiscellaneous
Bandit
Bandit
Posts: 76
Joined: Sun Feb 01, 2009 11:46 am

Re: JTAG Nand dump help

Post by MrMiscellaneous »

Congrats Man :D
Image
User avatar
CoFree
Robinhood
Robinhood
Posts: 13414
Joined: Wed Nov 07, 2007 1:38 pm
Location: In the Forest
Contact:

Re: JTAG Nand dump help

Post by CoFree »

yea man
damn good work
"FIGHTING TYRANNY in a TECHNOLOGICAL NOTTINGHAM"
Image
No Questions by PM.
Post Reply

Return to “J-Tag”