Flashing Lite-on dvd drive with iprep v008.6

[peacock]

hi guys...just thought of something....when i flash my drive....with iprep v008.6....and im using the ck3 pro with the probe.....i dont need to use the probe for anything do i ?.....nothing needs to be done to point 707 on the board ...does it ?...because in the vid tut cofree has already bridged the 707 point...?..do i have to solder this point as well ?..i dont really want to do any soldering as my soldering skills are not that good...., ive got the probe as well as the ck3 pro so what shall i do with the probe..?.....ta

[forsergi]

Hey guys,
just a quick question. I ordered CK 3 PRO with Probe, do i still need that famous VIA 6421 card? since i'll be plugging CK3 in a USB anyway?
thanks in advance.

[CoFree]

Hey guys,
just a quick question. I ordered CK 3 PRO with Probe, do i still need that famous VIA 6421 card? since i'll be plugging CK3 in a USB anyway?
thanks in advance.

man you are hi-jacking some one else thread.you should have started your on thread
ok
yes
you probably get the card.Ipep works good with iprep

im using the ck3 pro with the probe.....i dont need to use the probe for anything do i ?.....nothing needs to be done to point 707 on the board ...does it ?...because in the vid tut cofree has already bridged the 707 point...?..do i have to solder this point as well ?..i dont really want to do any soldering as my soldering skills are not that good...., ive got the probe as well as the ck3 pro so what shall i do with the probe..?..

there is a small whole before the 707 point that the tip of the probe goes into.
if you are going to use the probe then
NO you dont need to do any soldering.

[peacock]

there is a small whole before the 707 point that the tip of the probe goes into.
if you are going to use the probe then
NO you dont need to do any soldering

.

hi..yes ....at what point in the iprep video do i insert the probe into the small hole before 707 ?......is it before i press "enter" when typing in the dump command in iprep ?.....how long do i hold the probe in there ?.....sorry to ask, but this was not covered in the tut.....regards

[CoFree]

well
ive not messed with mine yet.
i would say
type dlit 1234567 12345 (your ser)
then put on the probe then hit enter and leave the probe in till all the dumping is done.

[peacock]

well
ive not messed with mine yet.
i would say
type dlit 1234567 12345 (your ser)
then put on the probe then hit enter and leave the probe in till all the dumping is done.

...yes that is what i thought....but can you please confirm that this is the right way as i dont want to mess it all up.....regards

that was a quick response ....lol, im just getting ready to go to work..lol 6am in the morning here....got peoples post to post.....

[CoFree]

it will not hurt anything to try and dump.
if its not right it just will not work.
after i was booted in dos on the flash i would put on the probe then do ever thing with the other hand
i guess that is going to be some what of a pain.

[peacock]

well


type dlit 1234567 12345 (your ser)
then put on the probe then hit enter and leave the probe in till all the dumping is done.

hi cofree...jus want to get something cleared up...you say put the probe in....and press "enter"..........now the next part of the tut requires that you open the tray half way etc...........now do i keep the probe still in r707 point or can i remove it ?..........im thinking i keep it in all the time whilst doing the half tray open part..up.until the key has been dumped and fimtool has started, i can then remove the probe from the r707 point ?....is that correct...

[CoFree]

that is right
you dont have to put the probe in till after you open the drive then close it half way.
turn on the drive power put the probe in.
then start with the probe staying in till you have all the files you need.

[peacock]

hi when dumping the keys a few times to the root of your usb stick just to make sure that they are the same each time....wont they get replaced each time because you have already dumped the keys there,.,,,,,,,,,,,,,,or do you dump the keys...boot into windows...goto the root of your usb stick.........and move the keys somewhere else .....do this about three times......then compare the two or three dumps you made of the keys..?????...ta

also

can you use any serial number or does it have to be the serial number for your xbox ?

[sadalius]

If you didn't copy them somewhere before re-dumping the information, they would get over written. What I generally do is rename them to something different that way they won't get over written and I can tell from which dump the files came from.

You can use any serial that you want to, but I generally try and stay with the actuall serial number so I can tell what 360 it came from. If your only doing your own, then it won't really matter, you could use 1234567 and 12345 or your realy serial number.

[peacock]

If you didn't copy them somewhere before re-dumping the information, they would get over written. What I generally do is rename them to something different that way they won't get over written and I can tell from which dump the files came from.

You can use any serial that you want to, but I generally try and stay with the actuall serial number so I can tell what 360 it came from. If your only doing your own, then it won't really matter, you could use 1234567 and 12345 or your realy serial number.

so basically if dump the files about 3 times with 3 different names , say liteon1, liteon2 and liteon3....i will have 3 files with these names in the root of the usb stick?....also after each dump...do i have to go through the whole process again of dumping the files each time?........ta

[CoFree]

i would
that is the point to start over each time
just to make sure you are getting the right files.

[peacock]

ok my ck3 pro and probe has arrived..everything connected up..boot up via usb flash drive..get ready to dump...before i enter "yes"....i put the probe on r707 point...light on probe and ck3 is green...once i put probe in r707 light on probe is blue and green..typed "y"...hit return and i get the message "gerimias dvdkey method failed"...any ideas why..ta

[CoFree]

you did open the tray half way, right?