RROD Question
RROD Question
I have a 360 that RROD and I have one that I mess up the drive for. Can I take the clamps from the messed up drive and transfer them to the RROD and make it work?
[url=http://www.xboxlc.com/profile/rkd2398[/url]
Please No Questions by PM, Use the board that's what it's for.
Please No Questions by PM, Use the board that's what it's for.
-
- Possible Ally of Robinhood
- Posts: 968
- Joined: Fri Jul 24, 2009 6:07 am
- Location: Somewhere in the forest
Re: RROD Question
I suppose u could try mate.
But most people just do the X-clamp fix removing the clamps alltogether
but go ahead and try it mate
Whats the worst that could happen
lol
But most people just do the X-clamp fix removing the clamps alltogether
but go ahead and try it mate
Whats the worst that could happen
lol
Re: RROD Question
What's the error on the rrod??
And what do you mean by the clamps? It normally requires the clamps are exchanged for bolts. A lot of the time, I heatgun as well. I think it adds (a little) more life into them...
And what do you mean by the clamps? It normally requires the clamps are exchanged for bolts. A lot of the time, I heatgun as well. I think it adds (a little) more life into them...
And if at first you don't succeed..? Order the damn card! http://tekgems.com/Products/la-pci22-vt6421a.htm
Mirc is a place to chat, post up on the site for help!!!
Re: RROD Question
I meant the clamps on bottom of board. I went ahead and tried and still didn't work. So I will get the stuff to do the X-Clamp.
The error is 0102 i believe which is unknown. Thanks for the reply's!!!
The error is 0102 i believe which is unknown. Thanks for the reply's!!!
[url=http://www.xboxlc.com/profile/rkd2398[/url]
Please No Questions by PM, Use the board that's what it's for.
Please No Questions by PM, Use the board that's what it's for.
- commando_lee
- Ally of Robinhood
- Posts: 1821
- Joined: Sun Apr 26, 2009 12:50 pm
- Location: Up high in the tree looking out for the Sheriff of Nottingham
Re: RROD Question
rkd2398 wrote:I meant the clamps on bottom of board. I went ahead and tried and still didn't work. So I will get the stuff to do the X-Clamp.
The error is 0102 i believe which is unknown. Thanks for the reply's!!!
0102 Error in the "Digital Backbone" (CPU/GPU/RAM), this is usually caused by a cold solder joint between the GPU and the mainboard.
................................................................RobinHoods Very Own
.......................................
I do this for the fun and pleasure in helping people. But this is NOT my job. Post up on the boards with your question and some body will help you dont use the PM system.
.......................................
I do this for the fun and pleasure in helping people. But this is NOT my job. Post up on the boards with your question and some body will help you dont use the PM system.
- sas67
- Possible Ally of Robinhood
- Posts: 319
- Joined: Wed Feb 18, 2009 2:29 pm
- Location: sunny scunny,uk
Re: RROD Question
i have fixed a few 0102 errors and have found the xclamp fix to work but only for a couple of months..i find heatgunning the board to be a much better option for resurrecting this fault
Re: RROD Question
Can someone post a pic to show where you need to apply heat when heat gunning the board?
[url=http://www.xboxlc.com/profile/rkd2398[/url]
Please No Questions by PM, Use the board that's what it's for.
Please No Questions by PM, Use the board that's what it's for.
Re: RROD Question
This is the tutorial I follow...
Insulation is just as important as the foil. I use bubblewrap, seems to do the job fine
Insulation is just as important as the foil. I use bubblewrap, seems to do the job fine
And if at first you don't succeed..? Order the damn card! http://tekgems.com/Products/la-pci22-vt6421a.htm
Mirc is a place to chat, post up on the site for help!!!