Robin Hoods Playground

whats Micro$oft's new Project Natal?

yeah man you know that half of these people are going to disagree about what we have said....but we are about 3000 miles away from each other..i know that its the xbox's...

Bro you should YouTube "Project Natal" it's a new add-on.
Check it out it's Big Brother scary cool.

aaahg!

I did another Dump, 2 of them actually. one with JF.43 and another with JF.1.26. The JF.1.26 allowed me to 'fix' my wrong serial numbers for my OPT/PCB and saved it where as the DSDBFixer would tell me too much information missing to save a fixed Dummy.bin

I have Both Dumps saved just in case.

Next...
Lite-On Erase, quick on/off and got the 72 status
"Drive returned Status 0x72
Manufacturer ID: 0x0
Device ID: 0x0
Flash Name: Unknown type
Flash Size: n/a"

Next, the final step...
Write.....?!! "Unknown flash type Write aborted !" ~WHAT!?~


huh.....help please?

CRYSIS ABORTED

All I needed to do was:
Power Cycle the CK3 Pro
Click Intro/Device ID
Click Write

Then you should see:
-------------------------------------------------------------------------
Sending Vendor Intro to port 0x9C00 <---that's my port, yours may be different

Serial flash found with Status 0x72

Sending Device ID request to port 0x9C00
Manufacturer ID: 0xC2
Device ID: 0x11
Flash Name: MXIC(MX25L2005)
Flash Size: 262144 bytes

Getting Status from port 0x9C00
SPi flash found with Status 0x72

Sending Chip Erase to Port 0x9C00
Writing target buffer to flash
Writing Bank 0: ................
Writing Bank 1: ................
Writing Bank 2: ................
Writing Bank 3: ................

Flash Verification Test !
Reading Bank 0: ................
Reading Bank 1: ................
Reading Bank 2: ................
Reading Bank 3: ................
Write verified OK !
-------------------------------------------------------------------------

YA BABY!
Now button her up and test her out....

BRB....

cool...hey how do you get them pictures up on the website like that...

Well folks, that's the trial-by-frustraiting-trial report on my XBox-360 Arcade Lite-On Mod.
When it was all said and done I followed:
CoFree's
Jungle Flasher on a lite-on 360 dvd drive with CK3 and Probe Video tutorial.
but using Jungle Flasher 0.1.62b and repairing the OPT/PCB serial labels when presented the option, then it built the Dummy.bin with no complaints.
I Freaked-out a bit when following the video it came time to hit that Write button.
Recycled the power switch on the CK3 Pro and then clicked the Intro/Device ID button.
Then clicked Write.

All done. I have learned even more this time around than last. I am now ready for my next Lite-on
BIG Thanx to CoFree, GiampyXBS, grandview, and xXxnottaxXx for all your support.

your welcome...

did you try rebuilding the dummy with Jungle Flasher 0.1.62 instead of Jungle Flasher 0.1.26b..and where did you get Jungle Flasher 0.1.26b at? and how do you put them images up...if you can tell me...

Sorry It wasn't JungleFlasher 0.1.26b it was 0.1.62b, I just edited my post for corrections, and yes I used it to repair the OPT/PCB serial info. I had taken those down earlier when I had it all apart.

I googled "Free picture uploads" and found:
http://tinypic.com/

To use just use your basic Paint app that comes with Windows.
have what you want on your desktop, hit your 'Print Screen' key on your keyboard.
Open paint and go-to the 'Edit' option at top and 'Paste'.
Once you have the pic on Paint choose the 'Select' button on the top Left (looks like a dotted square) and use this tool to highlight and stretch the select square over just the part of the picture you want to keep. Essentially cropping it.
once you got the borders of that Select tool on the area you want just right-click on that area and choose 'Cut'.
Now go back up to the top Left of Paint and click 'File' and 'New'.
You will be asked If you want to save changes, say no.
Now right-click on the blank canvas and 'Paste'.
Save picture by going to 'File' again and choose the JPEG format.

Save it any where you wish.
Goto the tinipic.com link and Upload your new JPEG pic by clicking on the 'Browse' and navigate it to that picture you saved.
Click 'Upload Now' and the next window you will be presented with a couple options on links to your pic.
Copy the text out of the 'IMG Code for Forums & Message Boards'
and use this to paste into your Replies on the message boards.

Thast it.
Its really easier than all that step-by-step tut I just went over.

thx...just for example

thx again...i learn new things all the time..

Right on bro.