Getting in there
Getting in there
It's one hell of a mission getting in a Wii
I can't get the Triwing screws out (the ones that are set back into the case) no matter what I try
anyone got any tips??
lilrevuk
I can't get the Triwing screws out (the ones that are set back into the case) no matter what I try
anyone got any tips??
lilrevuk


And if at first you don't succeed..? Order the damn card!

Mirc is a place to chat, post up on the site for help!!!
Re: Getting in there
man its been a while.
i think i used two different sizes of screwdriver.
man if need be before you mess it up.
i think i used two different sizes of screwdriver.
man if need be before you mess it up.
Re: Getting in there
Might post it as it is (if that's ok with my man). I've got down to those last 2 screws, it's really difficult to see if you are undoing them or not 



And if at first you don't succeed..? Order the damn card!

Mirc is a place to chat, post up on the site for help!!!
Re: Getting in there
I only use two screw drivers. Ones a philips #0 and the other is a tri-wing that I bought from gamersection.ca, here is the link to the tri-wing that I bought http://www.gamersection.ca/product_info ... f0qqbrejb1
Dunno if that helps you any, but thats what I used to open mine up with.
Dunno if that helps you any, but thats what I used to open mine up with.
Sadalius
No questions by PM please
No questions by PM please
Re: Getting in there
http://www.robinhoodsplayground.com/for ... ed7&t=1117#
Tip: When removing the case screws, use different colored Sharpies to color code the screws AND the holes they came from. I usually remove the screw first, color the head and then color the screwhole it came from. There are four (or is it 5?) different screw types (head/length) combinations.

Re: Getting in there
man
the last one i took all the way apart to put on a new case(it was mine)
was nuts i cant believe all the screws
the last one i took all the way apart to put on a new case(it was mine)
was nuts i cant believe all the screws

Re: Getting in there
There are alot of screws, different lengths and things, but I can only remember there being philips and tri-wing screws.
Sadalius
No questions by PM please
No questions by PM please
Re: Getting in there
yep your right as far as i remembersadalius wrote:There are alot of screws, different lengths and things, but I can only remember there being philips and tri-wing screws.
Re: Getting in there
I've got the right screwdrivers, just can't see if I'm undoing them or not....
I've got all the others out, just those 2
I've got all the others out, just those 2



And if at first you don't succeed..? Order the damn card!

Mirc is a place to chat, post up on the site for help!!!
Re: Getting in there
I'll post a few pic's soon, you only need to remove
5 Phillips screws and 8 Tri Wing screws for the case.
Phillips:
2 Small black phillips either side of the front panel, 2 even smaller phillips on the black side panel, 1 that hold the battery.
Tri-Wing:
2 Black ones under the stickers on the front panel, 2 Silver under the rear rubber feet, 2 Silver Under the black side panel, 1 Silver under the battery compartment, 1 Silver under the small sticker on the side near the battery, the one at the bottom.
Then 4 Phillips that are holding the DVD drive down.
Take care when lifting the drive, watch out for the ribbon cable.
5 Phillips screws and 8 Tri Wing screws for the case.
Phillips:
2 Small black phillips either side of the front panel, 2 even smaller phillips on the black side panel, 1 that hold the battery.
Tri-Wing:
2 Black ones under the stickers on the front panel, 2 Silver under the rear rubber feet, 2 Silver Under the black side panel, 1 Silver under the battery compartment, 1 Silver under the small sticker on the side near the battery, the one at the bottom.
Then 4 Phillips that are holding the DVD drive down.
Take care when lifting the drive, watch out for the ribbon cable.
