Robin Hoods Playground

where does the dumped firmware go, so that i can back it up? I used a floppy, and i see the backups folder and the CFW folder. When i try to copy the OFW from backups, it gives me an error, but it lets me copy the CFW. But dont i need the OFW?

yes you do
im not sure why you cant make a copy of it.
the floppy is not locked right.
eject it and restart your computer then put it back in and try.

When i use FW Tool box to check them, i get a good key out of CFW, but in OFW its something like 00000000FFFFFFFFF.

When i try to copy OFW it starts but then gives this error: Cannot copy BENQ-OFW: Data error (cyclic redundancy check).
What do u think?

there is no way i would use that firmware.
trash it all and start over

sorry man but that is what i would do

did you see firmtool run and build the hacked firmware.if so was the key good on the screen like in the video.was it a lot of different letters and numbers

Yes, it said success and had the key on the screen. what fw should i use?

yea but did the key look good.do you remember.well it dont matter i would start over .
ixtreme v1.4 12x speed is the firmware i use.


man if you will try to go in the chatroom.
ill try to help there and it new and want to make sure it works.
you have to put in a name

If either of your firmware OFW or CFW has what looks like a bad key, trash the whole thing like cofree said and start over till it's right. The keys must be good and match, otherwise it won't work.

I am concerned about an error I received while performing a DSAM operation
Im trying to flash a Samsung MS28 version drive
I have On board Via chipset VT8237 with the latest VIA drivers
I installed Microsoft .net framework
I performed the bad flash method
During my DSAM operation with IPREP 101 v006 I get a choice of
1. IDE primary
2. XTREME primary
3. VT8237 primary
so I chose the XTREME choice #2 (because you said so in your video), is this correct?

I need to confirm if I successfully dumped (DSAM) my firmware with IPREP 101 v006
IPREP program said I successfully retrieved the firmware 100%
BUT when Firmtool V1.1 tried to execute I received
“runtime error 162 at 0000:3638 General failure writing Drive C Abort, Retry, or Fail?”
should I be concerned about this since I did get a CFW and OFW file both at 256K


In my BACKUP folder from IPREP I get a 256K SAM-CFW file and a 256K SAM-OFW file

I opened the SAM-OFW bin file with Firmware toolbox v4.6
key comes up as 8B4622B5D868B8858E8D413FFD18387C

BUT!
I opened the SAM-CFW bin file with Firmware toolbox v4.6

key comes up as FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF

so what I did was edit the SAM-CFW hacked bin file with the key from the OFW file with toolbox v4.6?? (see attached screen shots)
will this work? from reading ALOT of forums on other sites this seems to be a common problem of "Firmtool"
Please advise.....thanks in advance…. supercooper

yes it looks good to me man
make sure your make a copy of that OFW and keep one off your computer so it cant get lost.
as long as you put that key in the hacked firmware then go to flashing.

man you should have started your on tread

It should work. Just make sure that your keys match in the OFW and the CFW when you finish with firmware toolbox and you should be ok to flash the cfw.

man go back and edit your post take your key off and the pictures off.
i would not put my key out there like that.
well i would but you shouldn't

If you're not sure, write the key down and dump again

check the key against the one you've just dumped, this way you'll be %100 sure you've got the right key (that's what I did anyway).....

cofree wrote:yes it looks good to me man
make sure your make a copy of that OFW and keep one off your computer so it cant get lost.
as long as you put that key in the hacked firmware then go to flashing.

man you should have started your on tread

translate "man!......you should have started your own thread LOL
at first I couldnt figure out what you meant with your reply? but I guess your in such a hurry this day and age...LOL

greetings cofree, really like your website, its well done and less confusing AND MORE UP TO DATE! most important..... than some other sites.

I have found TWO versions of "TEXTBOOKS TUTORIAL" of which neither one clarifies this on the front cover or the name of the file(or anywhere else), one uses "IPREP" and the other "Xtreme Boot Maker" and his video only covers using "xtreme bootmaker" where you show a video of Iprep (thanks)

which one is the best? Iprep or xtreme bootmaker? you seem to prefer IPREP??

but I had the other question to you asking should I of used DRIVE CHOICE

During my DSAM operation with IPREP 101 v006 I get a choice of
1. IDE primary
2. XTREME primary
3. VT8237 primary
so I chose the XTREME choice #2, is this correct? I would think choice 2 and 3 are the same drive??
please explain the difference if you dont mind....

sorry Im a noob and had no idea exposing your key code is bad, please explain....and i did remove the screenshots with my key code, thanks again

well man what you did is call hijacking a tread.
samuelsteven started this tread and we were working with him.you jumped in and started asking for something in his tread.
what you should have done is start a "new topic" and that would have been your tread.

is no problem at all i just thought you should know.

and the key thing
well lets say MR.M$ is looking a the site you just give him what he would want to know.
what key is going to be modded.
i dont think you have any thing to worry about .
its just something to keep in mind