Robin Hoods Playground

got my dummy file spoofed and started erasing the lite on. it start writing and the computer froze. i have looked at warrig's video and cofree's. every time i turn on the ck3 my computer freezes. the drive wont eject or do anything. any ideas would be grateful

If you pusth your drive tray back in it should un-mount.

Then close down Jungleflasher and you should be able to start your CK3 without the freezing.

You should have used the dummy file to create the liteon_cfw file before you started erasing.

You are going to have to use Iprep now to complete the flash as seen in Cofrees video.

chevyboy wrote:got my dummy file spoofed and started erasing the lite on. it start writing and the computer froze. i have looked at warrig's video and cofree's. every time i turn on the ck3 my computer freezes. the drive wont eject or do anything. any ideas would be grateful

TRY THIS then

Making your new firmware.
open jungle flasher and.

1. select load source firmware
2. yes to load ixtreme
3. click manual spoofing
4. click load key.bin (select your key.bin)
5. click load inquiry.bin (select your inquiry.bin)
6. click ok
7. click save to file
8. save as litcfw.bin

Now save this to iprep usb drive folder Backup\1234567\12345
you may need to make the folder 1234567 and then inside that folder create the folder 12345 save the litcfw.bin in there.

opening tray follow pic below then.....
Once you can open the tray pull the tray out fully and push half way back in. Now, hook it up to the PC using
Connectivity Kit and Sata, power on and flash your new firmware.

Flashing your liteon in iprep.
Start iprep and do the following:

1. flit 1234567 12345
2. follow instructions (power cycle drive etc)
3. select W to write firmware
4. type when asked litcfw.bin
Thats it youre flashed.

commando_lee wrote:

chevyboy wrote:got my dummy file spoofed and started erasing the lite on. it start writing and the computer froze. i have looked at warrig's video and cofree's. every time i turn on the ck3 my computer freezes. the drive wont eject or do anything. any ideas would be grateful

TRY THIS then

Making your new firmware.
open jungle flasher and.

1. select load source firmware
2. yes to load ixtreme
3. click manual spoofing
4. click load key.bin (select your key.bin)
5. click load inquiry.bin (select your inquiry.bin)
6. click ok
7. click save to file
8. save as litcfw.bin

Now save this to iprep usb drive folder Backup\1234567\12345
you may need to make the folder 1234567 and then inside that folder create the folder 12345 save the litcfw.bin in there.

opening tray follow pic below then.....
Once you can open the tray pull the tray out fully and push half way back in. Now, hook it up to the PC using
Connectivity Kit and Sata, power on and flash your new firmware.

Flashing your liteon in iprep.
Start iprep and do the following:

1. flit 1234567 12345
2. follow instructions (power cycle drive etc)
3. select W to write firmware
4. type when asked litcfw.bin
Thats it youre flashed.

sorry i am a noob. i got the litecfw.bin file. not sure were to make the new folders name 1234567 12345 to put the the litecfw file in

chevyboy wrote:

commando_lee wrote:

chevyboy wrote:got my dummy file spoofed and started erasing the lite on. it start writing and the computer froze. i have looked at warrig's video and cofree's. every time i turn on the ck3 my computer freezes. the drive wont eject or do anything. any ideas would be grateful

TRY THIS then

Making your new firmware.
open jungle flasher and.

1. select load source firmware
2. yes to load ixtreme
3. click manual spoofing
4. click load key.bin (select your key.bin)
5. click load inquiry.bin (select your inquiry.bin)
6. click ok
7. click save to file
8. save as litcfw.bin

Now save this to iprep usb drive folder Backup\1234567\12345
you may need to make the folder 1234567 and then inside that folder create the folder 12345 save the litcfw.bin in there.

opening tray follow pic below then.....
Once you can open the tray pull the tray out fully and push half way back in. Now, hook it up to the PC using
Connectivity Kit and Sata, power on and flash your new firmware.

Flashing your liteon in iprep.
Start iprep and do the following:

1. flit 1234567 12345
2. follow instructions (power cycle drive etc)
3. select W to write firmware
4. type when asked litcfw.bin
Thats it youre flashed.

sorry i am a noob. i got the litecfw.bin file. not sure were to make the new folders name 1234567 12345 to put the the litecfw file in

can u do this in dos? i have my drive connected and it says that the port that i am using is status 0x80
i know it needs to be in 0x72 if i am right

You will need to rename the file LITCFW.bin not litecfw.bin

have you made your bootable iprep usb drive??

If so do this

1) open the usb device
2) there is a folder called backups (open it)
3) make a new folder inside that and call it 1234567
4) open that folder
5) make a new folder inside that and call it 12345
6) Open that, then inside that copy & paste the LITCFW.bin file
7) close down the screen

Then follow the directions i gave

commando_lee wrote:You will need to rename the file LITCFW.bin not litecfw.bin

have you made your bootable iprep usb drive??

If so do this

1) open the usb device
2) there is a folder called backups (open it)
3) make a new folder inside that and call it 1234567
4) open that folder
5) make a new folder inside that and call it 12345
6) Open that, then inside that copy & paste the LITCFW.bin file
7) close down the screen

Then follow the directions i gave

no how would i make iprep bootable usb drive?

chevyboy wrote:

commando_lee wrote:You will need to rename the file LITCFW.bin not litecfw.bin

have you made your bootable iprep usb drive??

If so do this

1) open the usb device
2) there is a folder called backups (open it)
3) make a new folder inside that and call it 1234567
4) open that folder
5) make a new folder inside that and call it 12345
6) Open that, then inside that copy & paste the LITCFW.bin file
7) close down the screen

Then follow the directions i gave

no how would i make iprep bootable usb drive?

First of all you will need a usb flash device.


Follow this tutorial up untill your iprep device is done.

viewtopic.php?f=195&t=5130" onclick="window.open(this.href);return false;

click the link below to download iprep

download/file.php?id=614" onclick="window.open(this.href);return false;

you will need to get the lite-on hacked firmware from xbins if you dont have it