Robin Hoods Playground

I am trying to flash a lite on drive with iprep using a conectivity kit and prob. I followed the tut on youtube to a tee but I keep getting the error dvdkey invalid here are my steps.
1. Make bootable flash drive (I used com port 3 USB) using iprep
2. Reboot. Then put in dlit and my serial hit enter
3. it promps me to do the open tray method I do and then I put the probe in r707 hole
4. hit y then enter and I get DVDKey invalid
I have also tried port 1 but i get the same msg i've done another 360 in jf but i cant get it to work now because it keeps freezing I have tried everything I can think of but no luck : (

With the open tray, is it half open or fully open? It should only be half

That pic looks like hes using usb. also there dont look like a 9pin serial.

serial - usb or any type of usb will not work with iprep.

You will need a RS232 cable to enable you to dump the key

HaGGardSmurf wrote:With the open tray, is it half open or fully open? It should only be half

yes I have the tray half way open, and I didnt know that the usb wont work in iprep I tried using jf 1.66 instead I followed the instructions and installed the portio32 and follow cofree's video and it detects the drive but everytime I go to extract the key it freezes and again i am using com port 3 (usb) but it should work btw I am using on board sata its nvidia motherboard so no via card to uninstall....... any suggestions or should I just get the cable and hope that it will solve my problems..... and can I buy that RS232 cable at any electronics store or do I have to order online

Renzo0202 wrote:

HaGGardSmurf wrote:With the open tray, is it half open or fully open? It should only be half

yes I have the tray half way open, and I didnt know that the usb wont work in iprep I tried using jf 1.66 instead I followed the instructions and installed the portio32 and follow cofree's video and it detects the drive but everytime I go to extract the key it freezes and again i am using com port 3 (usb) but it should work btw I am using on board sata its nvidia motherboard so no via card to uninstall....... any suggestions or should I just get the cable and hope that it will solve my problems..... and can I buy that RS232 cable at any electronics store or do I have to order online

Yeah you will need a rs232 9 pin male - female cable. Could also be possible that the sata controller is not compatable

commando_lee wrote:

Renzo0202 wrote:

HaGGardSmurf wrote:With the open tray, is it half open or fully open? It should only be half

yes I have the tray half way open, and I didnt know that the usb wont work in iprep I tried using jf 1.66 instead I followed the instructions and installed the portio32 and follow cofree's video and it detects the drive but everytime I go to extract the key it freezes and again i am using com port 3 (usb) but it should work btw I am using on board sata its nvidia motherboard so no via card to uninstall....... any suggestions or should I just get the cable and hope that it will solve my problems..... and can I buy that RS232 cable at any electronics store or do I have to order online

Yeah you will need a rs232 9 pin male - female cable. Could also be possible that the sata controller is not compatable

ok I will try that hopefully it will work.....and I my sata controller should work I managed to flash my drive which is a lite on with jf 1.62 (have no idea how i did it but it worked) this is the first time i ran into this problem but I will order the cord and let you know how it works out thanks for the help

ok I got the rs 232 cable in the mail and followed cofrees tut on youtube but its still giving me dvdkey invalid???? help

Have to make sure that when you setup iprep that you specify the right serial (COM) port and the right sata port.

sadalius wrote:Have to make sure that when you setup iprep that you specify the right serial (COM) port and the right sata port.

yea its on com 1 and I have the right sata port could it be my keygrabber thats not working right i bought it from here http://kreon.offerdahl.org/" onclick="window.open(this.href);return false; i think its something im doing wrong but i donno wat

I'm not familiar with the keygrabber. But it should work similar to the other ones on the market. If the keygrabber is in order, and you have specified the right com port and sata port, it should work given the sata port that your connected to is compatible.

sadalius wrote:I'm not familiar with the keygrabber. But it should work similar to the other ones on the market. If the keygrabber is in order, and you have specified the right com port and sata port, it should work given the sata port that your connected to is compatible.

ok I will try again from step one and make sure I'm doing everything right and double checking I will post pics of what im doing if it doesnt work again this time and see if you can see something im doing wrong......but thanks for all the help and working with me

well you guy kind luck that your motherboard have rs232 and what i hear i can't use PCI Express Serial Cards with iprep. so i'm kind shit out of luck on using iprep

darktron wrote:well you guy kind luck that your motherboard have rs232 and what i hear i can't use PCI Express Serial Cards with iprep. so i'm kind shit out of luck on using iprep

yeah I only have trouble with lite ons I've flashed plenty of other drives with iprep and didnt use rs232 or usb hook up

well soon i be making a new pc so i can use rs232.