lite-on

Post by **bigtize6920** » Fri May 01, 2009 7:42 pm

I was wondering if there was another way to flash the lite-on other then jungle flasher. The reason i am asking is because of the the freezing when trying to erase the lite-on using jungle flasher, or has there been a fix yet?

Post by **technoe** » Fri May 01, 2009 7:50 pm

You can and should probably use iPrep V009 for flashing any drive. iPrep does all of the flashing in DOS. You can download it from our downloads section here. I'm assuming you have a CK3 of some sort, you will need the serial cable to do the flashing with iPrep if the drive has never been flashed before. If the drive has iXtreme 1.5 or higher the drive will dump and flash through the sata port.

Post by **CoFree** » Fri May 01, 2009 9:43 pm

technoe wrote:If the drive has iXtreme 1.5 or higher the drive will dump and flash through the sata port.

i am going to check this
it was my understanding iprep still needed the com cable even on a reflash

Post by **commando_lee** » Sun May 03, 2009 1:18 pm

i tryed to flash a lite-on thru IPREP using a rs232 straight cable and ck3 with probe attachment. But i kept getting the error germains key method failed and it wouldnt go from there! any ideas what i might had done wrong! at least ill know for next time

Post by **CoFree** » Sun May 03, 2009 1:47 pm

did you have the tray in the half closed spot

Post by **commando_lee** » Sun May 03, 2009 1:52 pm

CoFree wrote:did you have the tray in the half closed spot

yeah i had it in half way . i also tryed it 3/4.

Post by **CoFree** » Sun May 03, 2009 1:54 pm

did you put the probe on at the very start like in the video

Post by **commando_lee** » Sun May 03, 2009 1:57 pm

CoFree wrote:did you put the probe on at the very start like in the video

i dont think i did i might have put it on just b4 i pressed enter Could that have been the problem ? also i got a 360 with 6038drive flashed with ixtreme1.4 what error message or what would happen if a game that uses wave3 was put in?

Post by **CoFree** » Sun May 03, 2009 2:02 pm

commando_lee wrote:dont think i did i might have put it on just b4 i pressed enter

you need to put the probe on before you hit anything

commando_lee wrote:also i got a 360 with 6038drive flashed with ixtreme1.4

it will not play a wave 3 game
you will need to update the benq firmware to v1.51 to play a wave 3 game

Post by **commando_lee** » Sun May 03, 2009 2:03 pm

would the xbox 360 logo screen just freze?

Post by **CoFree** » Sun May 03, 2009 2:05 pm

dont know i did the update
i dont take to many chances with my game room consoles

Post by **commando_lee** » Sun May 03, 2009 2:10 pm

which program can i use to make a copy of my original games so that the kids dont break the original cause dont fancy paying £40 a time to replace it.

Post by **iamwatt** » Sun May 03, 2009 2:48 pm

commando_lee wrote:would the xbox 360 logo screen just freze?

this happens when you don't have the 1.51 firmaware on the drive and you put a 3rd wave game in.

you'll need to update the firmware. . .

Post by **commando_lee** » Sun May 03, 2009 4:54 pm

iamwatt wrote:
commando_lee wrote:would the xbox 360 logo screen just freze?
this happens when you don't have the 1.51 firmaware on the drive and you put a 3rd wave game in.

you'll need to update the firmware. . .

i have updated the firmware and yeah it works, but the game changed the dashboard. Should that have happend?

Post by **iamwatt** » Sun May 03, 2009 5:18 pm

yeap, that's the purpose of the 3rd wave. . .

so is ya problem solved, because im not even sure what the issue was anymore lol!

Robin Hoods Playground

lite-on

lite-on

Re: lite-on

Re: lite-on

Re: lite-on

Re: lite-on

Re: lite-on

Re: lite-on

Re: lite-on

Re: lite-on

Re: lite-on

Re: lite-on

Re: lite-on

Re: lite-on

Re: lite-on

Re: lite-on