My Lite-On says Play DVD/Open Tray after reflashing

[croofed@ymail.com]

Ok, so When i bought my 360, the Lite-On is already flashed with iX 1.5. Now I want to reflash it with ix1.6.
I already dummy from iXtreme successfully.
Because this is my 1st time, when the drive sequence thing (when I must power cycle the drive) my power cycle took it a little longer time so it didn't show as windbond thing. But, after I click the Lite-On erase again and doing the perfect power cycle and also finish writing. When I want to play backed up games it just say 'Play DVD'. Sometimes it says 'Open Tray'.
When I check it again with JF, my drive key is 55AA55AA55AA55AA55AA55AA55AA55AA.
How to recover it? Please, I'm really desperate...

[commando_lee]

it looks like you have a bad key. do you have the original bin files you should have 4 if you did it right when extracting them??

[croofed@ymail.com]

How to get the original files?
When I bought my 360, its already flashed.

[commando_lee]

How to get the original files?
When I bought my 360, its already flashed.

did jungle flasher ask you to save any files like these - key.bin - inquiry.bin - identify.bin - dummy.bin ???

[croofed@ymail.com]

Yes. JF asked it when I click the 'Dummy from iXtreme'.

[dalecheesy]

Load the saved dummy.bin into jungle and check the key. If its the same as above or with lots of recurring characters or comes up as invalid its knackered mate.

[croofed@ymail.com]

Okay, I have load it w/ my 1st dummy.bin. And the key isn't recurring, but it give the random of number and alphabet.
Now what am I gonna to do? Can I start over again?

[dalecheesy]

Yeah just start again by loading the source from the dummy.bin

[croofed@ymail.com]

How to?
After I connected my Drive, do I need to click 'Dummy from iXtreme'?
Is the step are the same? Am I need to click the 'Spoof Source to Target' ?
Please if you can give me the correct steps again. I'm really confused and sad...

[dalecheesy]

When you click on the load source firmware and select your dummy.bin you should get a pop up asking do you wish to autoload liteon ixtreme, click yes and follow the procedure like before.

[croofed@ymail.com]

Yeah Thanks.
the Point is, The key from the Source and Target must be the same, right?
I have load the dummy.bin, but in the Firmware type it didn't show as DVDkey32 but it show as iXtreme 1.50 (my previously fw). Is that alright?

[dalecheesy]

Yip as long as the keys match thats the important bit. When you load it in if you select autoload the key should automatically be transferred into the new ixtreme for you ready to be flashed over.

Ps: before you go any further save the dummy.bin to a couple of places and maybe email it to yourself as its crucial if anything goes wrong also click on the save file button after its loaded into the new ixtreme and do the same for that one.

[croofed@ymail.com]

Ow man. Thanks. About the firmware type that won't show the DVDKey32 instead of the previoulsy iXtreme files, is not a problem, am I right?

[dalecheesy]

Are you on the FirmTool 32 tab? If so then yeah it'll show up as whatever your dumped dummy.bin was (if it had ixtreme 1.5 on when you dumped it then it'll show that as the firmware type) as long as the keys match up when it loads into ixtreme 1.6 then you're good to go.

[croofed@ymail.com]

Yeah. The point is just the same key, right.
Ok, I'll try again now.