Write Verify Failed BenQ

[hyperdrive]

Hey, as I have read many similar situations to my own, I just want a bit of reassurance.

I flashed my BenQ with iX 1.6, all seemed to go well, but it shows that the "write verify failed"

I tried once more, same thing, so I pressed outro/reset, put the drive back in the xbox and it boots backups and originals fine. Did it all go ok?

It said in JF that it had wrote, but not verified, and it still plays games.

As you can probably guess I'm just a little confused.

VIA Sata, JF 1.6, iX 1.6. Thanks if any of you guys can put my mind at ease

the steps i took;

1. benq unlock
2. read
3. load ix 1.6, spoof key ok.
4. This is where I think I went wrong, my first flash so I was anxious, I never saved the CFW file I just pressed write.
5. it said erasing, then wrote 4 banks
6. write verfiy failed
7. games boot

Main Question: Does it look like it went ok, or will I have to do it over again?

I think it went ok as the BenQ unlock no longer works and I believe that only works on anything less than 1.5?

If it looks ok I'd rather it stay as it is rather than try again, as I don't feel I am skilled enough to do the half open tray to unlock.

My JF.log





~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

JungleFlasher 0.1.60 Beta

Session Started Tue May 19 17:43:28 2009




This is a 32 bit process running on a 32 bit CPU

PortIO is installed and running.

Found 8 I/O Ports.

Found 2 Com Ports.

Found 10 windows drives.

Found 1 CD/DVD drives.





Sending Magic Keys to Drive on port 0x0xA400

..........................................

Done!

Sending Vendor Intro

Requesting Device ID

Manufacturer ID: 0xC2

Device ID: 0x11

Flash Name: MXIC(MX25L2005)

Flash Size: 262144 bytes



Getting Status from port 0xA400

Serial flash found with Status 0x73



Reading Bank 0: ................

Reading Bank 1: ................

Reading Bank 2: ................

Reading Bank 3: ................



Benq Dump file saved to C:\Desktop\iX_v1.6_pack\BenQ_iXtreme-THX_v1.6\BENQ-OFW.bin



Loading MTK_Flash source file

Inquiry string found

Identify string found

DVD key found @ 0xE030 key is **************** Valid Key (Edited)

Firmware is Benq OSIG: PBDS VAD6038-64930C

Firmware type is: iXtreme v1.4-8xNonStealth



Auto-Loading target file C:\Desktop\JungleFlasher.0.1.60.Beta\JungleFlasher v0.1.60 Beta\firmware\ix16-benq.bin

Target File MD5 hash is: f36c85c5bfba325b283417f8643d7c27

Genuine Benq iXtreme 1.6

Inquiry string found

Identify string found

DVD key found @ 0xE030 key is 77777777777777777777777777777777

Firmware is Benq OSIG: PBDS VAD6038-64930C

Firmware type is: iXtreme v1.60-12x-FINAL-VAD6038



Spoofing Target

DVD Key copied to target

Inquiry strings identical

Identify strings identical

0xFF00 area copied for Benq to Benq



Getting Status from port 0xA400

SPi flash found with Status 0x73



Sending Chip Erase to Port 0xA400

Writing target buffer to flash

Writing Bank 0: ................

Writing Bank 1: ................

Writing Bank 2: ................

Writing Bank 3: ................



Flash Verification Test !

Reading Bank 0: ................

Reading Bank 1: ................

Reading Bank 2: ................

Reading Bank 3: ................

Write Verify Failed !

Loading target file C:\Desktop\iX_v1.6_pack\BenQ_iXtreme-THX_v1.6\ix16-benq.bin

Target File MD5 hash is: f36c85c5bfba325b283417f8643d7c27

Genuine Benq iXtreme 1.6

Inquiry string found

Identify string found

DVD key found @ 0xE030 key is 77777777777777777777777777777777

Firmware is Benq OSIG: PBDS VAD6038-64930C

Firmware type is: iXtreme v1.60-12x-FINAL-VAD6038



Spoofing Target

DVD Key copied to target

Inquiry strings identical

Identify strings identical

0xFF00 area copied for Benq to Benq



Getting Status from port 0xA400

SPi flash found with Status 0x73



Sending Chip Erase to Port 0xA400

Writing target buffer to flash

Writing Bank 0: ................

Writing Bank 1: ................

Writing Bank 2: ................

Writing Bank 3: ................



Flash Verification Test !

Reading Bank 0: ................

Reading Bank 1: ................

Reading Bank 2: ................

Reading Bank 3: ................

Write Verify Failed !

Key data saved to C:\Desktop\Key.bin



Sending Vendor Outro to port 0xA400



Sending Magic Keys to Drive on port 0x0xA400

..........................................

Done!

Sending Vendor Intro

Vendor Intro Failed

Sending Vendor Intro to port 0xA400

Status 0x51

[rkd2398]

Looking at that log where it says the target file, did you click spoof to target? The keys have to match up.

[hyperdrive]

Yes I did, well JFlasher did it on Auto loading of the IX f/w

I also done it manually, I have just edited out my DVD Key from the Original Post.

As it is all working still the key is not an issue really,

I think its basically because I flashed the Target from the memory rather than saving it as BENCFW.bin

Therefore reasoning would lead me to believe there is no file for it to verify against?

I'm just curious as to why it said verify failed but still works ok.

98% sure it was just because I never saved to file, as I assumed this was just for use with iPrep etc.


Here is the segment from the log.

Auto-Loading target file C:\Documents and Settings\Barry\Desktop\JungleFlasher.0.1.60.Beta\JungleFlasher v0.1.60 Beta\firmware\ix16-benq.bin

Target File MD5 hash is: f36c85c5bfba325b283417f8643d7c27

Genuine Benq iXtreme 1.6

Inquiry string found

Identify string found

DVD key found @ 0xE030 key is 77777777777777777777777777777777

Firmware is Benq OSIG: PBDS VAD6038-64930C

Firmware type is: iXtreme v1.60-12x-FINAL-VAD6038



Spoofing Target

DVD Key copied to target

Inquiry strings identical

Identify strings identical

0xFF00 area copied for Benq to Benq

[technoe]

Man, I would flash it with iPrep just to be safe. There's nothing wrong with taking a little extra time to do things right.

[hyperdrive]

I was going to do that but I have no USB bootable pc's, and Cofree advised against using a floppy.

I think I'm ok, everything seems to be working, just a bug in JF, probably?

I guess the only real way of knowing is making a non stealth backup and see if it boots or not, but if it was a bad flash I guess the drive would just not operate or give me an error.

Any further input would be great.

Cheers

[technoe]

Know that if you boot a non-stealth game you WILL get banned.

[CoFree]

technoe
is right dont put a bad game in just to see
the console will log that and ban your ass when you get on live

never play non-stealth games man

[hyperdrive]

I wasn't going to I was just thinking out loud.

I'm going to try Hawx see how it goes.

Thanks for all the help and advice guys.