Lite-On Bricked..Power upside down..

[Kurdy]

Hi,

I tried to flash my drive today. But by a mistake ive put the power cord upside down on the drive. Its not working now. I opened my drive and r207 is black now..it was not before.
How can i fix my drive?
I took yesterday a photo of my drive and now i can see whats different after i did the power upside down..the only different is the r207 its black now there is no dot on it..
Can u please take a look at these photos and tell me what i can do to fix this problem?

Before: http://img262.imageshack.us/i/dsc01728n.jpg/" onclick="window.open(this.href);return false;

Now: http://img697.imageshack.us/i/dsc01733.jpg/" onclick="window.open(this.href);return false;

Thanks and sorry for bothering..

Kurdy

[djshauny1]

Sorry but it sound like you have fried the drive
If u dont have the info from the drive then im affraid its game over

[Kurdy]

How much game over? Come on..there must be a way to fix this?? And yes i dont have my dvd key

[rkd2398]

Without the key, dummy and inquiry, there is no way to build the CFW. Game over as in it will only play dvd's when you stick a new drive in it. Sorry Bro.

[dalecheesy]

Well it might be worth a try but you could technically try bridging the r207 link ( zero ohm) with a wire bridge if you've tested it with a multimeter for continuity and its failed and keep your fingers crossed that that was the only damage to the drive. If that doesnt work it would require a strip down for broken tracks etc and as the guys have said it will be game over if its caused chip damage. On a side note the newer versions of the ck3 have pptc protection to prevent this happening.

[after_burners]

u can try bridging like dalecheesy said uve nothing 2 loose really. its just really bad luck but it does happen

[Kurdy]

Thanks guys for helping.
I solder r207 in this way. is it good or not?

http://img406.imageshack.us/img406/1277/dsc01739d.jpg" onclick="window.open(this.href);return false;

The drive spins few seconds than it stops..is this good or not?
Bytheway..some said if u solder this 2 holes it will work? http://server2.uploadit.org/files/elcap19-photo.jpg" onclick="window.open(this.href);return false;
is that true? and whats the point of soldering this?

[iamwatt]

you soldered the wrong thing. its the r707 points. . . those small points to the left of where you soldered and you can just use a screw driver to bridge them. . .

[Kurdy]

you soldered the wrong thing. its the r707 points. . . those small points to the left of where you soldered and you can just use a screw driver to bridge them. . .

Can you please draw on one of this pictures in paint to show me what i should solder and what about the r207? is it ok to have the solder there? should i put the screwdriver just on the r707 or r707+708

[iamwatt]

i put the scewdriver across the r707 point, thats the only thing that should be bridged. nothing else. . .

[Kurdy]

This hole?

So i put a screwdriver on this point and thats it?

[iamwatt]

yeap, not on the hole but across those two points

[Kurdy]

yeap, not on the hole but across those two points

Sorry for bothering..but i dont get it..which part do you mean? Please if you can draw i will appreciate it..

[dalecheesy]

Bridge the r707 points with either a wire or a screwdriver or similar (not the hole as thats used if you're using a probe instead, same as in this pic but ignore the 708 points.)



Another pic:

[Kurdy]

Thank u so much..i will try it