hmmmm 7s back to stock problem in jf ?

[GRASSASS]

hello all

iv held off doing this upto 1.9 as i had a legal hit but its just 2rrod on me while codd'ing 3 hours ago sod's law

so i have to flash my liteon 7s to stock using jungleflasher 1.83 (last 1) then upto 1.9

my 1st serious problem is im not sure which of my 2 liteon 7s go with which fw backup ... so i guessed using the date the folder was created and the amount of dust in the console - dont laugh lol

anyhow iv decided upon the fw im using and created my fw using the stock fw and im using shootsteele's vid with jf 1.66b for 7s drive...
i have loaded my cfw into jf (which shows drive but no key-i guess thats because it has lt1 on) and hooked up the drive which shows in jf ... then i clicked on liteon erase in 360tools in jf, and it warned me it cannot verify the key i clicked ok to carry on and the warning for am i realy sure i want to carry on- i clicked yes and then jf says status 0x0 ??? well this is its log the stage 2 fail i assume is cos of not being able to see key :-

Firmware Osig: [PLDS DG-16D2S 7485]
Firmware is: iXtreme LT

Stage 2 failed

Sending Lite-On-Erase request to port 0xBF00
..............
Drive returned Status 0x0
....................
Device Intro failed!

im unsure of what to do, the drive doesnt open (i know iv been here b4 but used iprep & dos-i miss them)
i used jf to go back to stock with a sammy the other day so the drivers are fine ?

i just clicked outro atareset and the drive info has dissapeared ??? still dont open or close ?

can any body point me in the right direction

[GRASSASS]

just retraced my steps got it into vendor mode and then i click write... but now its freezing at bank 1 ?

?
put it back into vendor and now im getting :-
Sending Lite-On-Erase request to port 0xBF00
..............
Drive returned Status 0x0
.....
Serial flash found with Status 0x72
Manufacturer ID: 0x0
Device ID: 0x0

im uncomfortable not knowing how to use jf ?
can anybody help me ?

[CoFree]

you flash back to stock the same way you flashed in a hacked firmware
then take the update
then flash back to the new hacked firmware
watch some of the liteon flash guides for jungle flasher
they should help

[gazzer]

theres a 1.84 j.f out so get that to start with. if the drive is erased just open j.f put your cfw in source and the 7 series stock firmware in target and spoof source to target. now you have said you would rarther use iprep so get the 10.7 iprep and use that to write the firmware you have just made with jf just change the file so iprep will recognise it THEN L74 1234567 12345 W AT THE END it will go straight to the write process i presume you know all about the iprep method it works

[GRASSASS]

cheers cofree / gazza

i think iv finally killed a liteon

i have a usb stick with iprep 10.7 on it so i tried the way i know -all drives unplugged- type dos then dosflash yaddayadda but when i choose my drive number it said "unknown flash chip" ? wahh ! it was working ?!?!?!

is this fixable ? i havent got a bloody clue of the problem but like i said im unsure of which fw backup belongs to which drive :headshake:
if the liteon is fixable, and i flash the wrong key to it will it die ? or will i get the chance to reflash it with the other fw backup ?

in iprep after typing dosflash i didnt get to type l-o-eras ? it just went straight to choosing a drive ? does iprep method still work ?

"i know theres a few mashed up questions there - sorry if its not inteligable but seriously thanks for your help"

i gota go sleep bbl

[GRASSASS]

well ? no luck ! does the iprep stick need me to rename the via drivers to orig ?

devostated !

[CoFree]

man you are going to have to use jungle flasher
try it on a pv that has onbo sata
no pci sata card
just onbo sata

there is a way to use jungle flasher on a via card but its a pain

[GRASSASS]

got it bk to stock using iprep 10.7 with dos

i just needed to re-rename the via driver

now cofree all we need is 1 of your awesome video tutorials for this new process
( i know its similar to the first but still man it is a different way what with these all round firmwares for liteon )

cheers guys thats why i like it here no bull just plain old good help

[gazzer]

if you have got back to stock with the iprep 10.7 once you have taken the update you can do the same procedure again. load the cfw from your first flash in j.f source and the lt 1.9 in target spoof source to target . and save the file on your desk top . the file you saved on the desk top will need changing from lite_cfw to l74cfw just assuming it is a liteon to the file name that the iprep program will recognise put that file in the backup folder of iprep that file should be in 2 folders call the first folder 1234567 and second folder 12345 put the file you made on the desktop with jf in folder 12345 then drag that folder into 1234567 folder drag that into ipreps back up folder now boot into dos on the iprep usb stick once its opened up go through procedure if its liteon or whatever drive lets say L74 1234567 12345 W just make sure you put the w at the end it will write the cfw file you put in the backup folder in iprep just follow instructions and your drive will be flashed . And the answer to the question about flashing it with the wrong file that wont stop you flashing it again going the iprep route. this is in your case as you have two files and you are not sure which is the right one . just one more thing you dont have to do half tray open when you just want to write the firmware just hook up to via card and ck3 for power


iPrep v10.7 lite-on v74 video guide

[GRASSASS]

cheers gazzer il let you know if im lucky twice in 1 week lol

altho i might leave it a bit and play cod

il save your little post for l8r perusal