Robin Hoods Playground

It should be fine. Keep in mind that if you use a different computer, you'll have to set iprep back up from scratch. When you initially set it up, the sata ports are assigned for that computer, they will more than likely be different from computer to computer, even if you install the sata card from one computer to a different one, so you'll want to run the iprep setup on the computer your going to be doing the key dumping and flashing from.

sadalius wrote:It should be fine. Keep in mind that if you use a different computer, you'll have to set iprep back up from scratch. When you initially set it up, the sata ports are assigned for that computer, they will more than likely be different from computer to computer, even if you install the sata card from one computer to a different one, so you'll want to run the iprep setup on the computer your going to be doing the key dumping and flashing from.

hi - can you explain a bit more when you say "even if you install the sata card from one computer to a different one, so you'll want to run the iprep setup on the computer your going to be doing the key dumping and flashing from"....i can understand installing the sata card and installing the drivers, but not too sure about "setting up iprep again".....what do you mean ?

also

in the video yut near the end after you have erased the liteon firmware...how do you turn the power to the liteon off and then back on again ?....do you simply pull the power cable out or use the on/off button the ck3 pro ?....

also

just after this erasing part it asks "enter the number of the ATAPI drive , ie in the tut its 6?"....how do you know which is the right one for my drive ?...will it be displaying "no identify possible"...because theres no firmware on it ?

also bought this serial cable...will it do ?
http://www.morecomputers.com/extra.asp? ... er=Froogle" onclick="window.open(this.href);return false;

sorry for so many questions again.....
regards

peacock wrote:can you explain a bit more when you say "even if you install the sata card from one computer to a different one, so you'll want to run the iprep setup on the computer your going to be doing the key dumping and flashing from

you have to build the usb flasj drive on the computer you are going to dump/flash with.
if you change computers the port address will be different and that will cause you trouble.

peacock wrote:but not too sure about "setting up iprep again".....what do you mean ?

well you would need to have iprep build the isb flash again so the port address would be right
the port address is a set of letters and/or numbers that the computer will give the sata port.iprep must have that info right or the dump/flash will not work.

peacock wrote:how do you turn the power to the liteon off and then back on again

there is a small on/off switch on the ck3.you will use that to power off the drive.

peacock wrote:just after this erasing part it asks "enter the number of the ATAPI drive , ie in the tut its 6?"....how do you know which is the right one for my drive

that can be a little tricky.It will be easy to see which one it is before you dump.you will be able to read the info for the drives and see which one it is.
after the erase you just have to remember which one it was.
it will be the same one but it will not list all the info because it is now blank.

peacock wrote:also bought this serial cable...will it do ?
http://www.morecomputers.com/extra.asp" onclick="window.open(this.href);return false;? ... er=Froogle

yep should be fine.

hi guys...ok, made the bootable flash drive (drive F)......rebboted pc......pressed f11 to select boot from sandisk usb flash drive (see pic i posted)......however it justs hangs on the following screen...see pic...
does everything have to be connected up when booting from the usb drive ? ie, sata cable to ck3 pro and drive............, power cable to ck3 .........., power from ck3 to drive...... r com cable from ck3 to rs232 port on back of pc....because i havnt got anything connected yet....?

nothing as /should be hook up till up are booted up on the flash
its not booting on the flash
you will see the windows 98 flash by like the video.when it works
you may need to try a different usb flash or check the setting in your bios

CoFree wrote:nothing as /should be hook up till up are booted up on the flash
its not booting on the flash
you will see the windows 98 flash by like the video.when it works
you may need to try a different usb flash or check the setting in your bios

hi - oh dear this is getting a bit too techy for me.. ...what am i suppose to look for in the bios and change?..

Just disconnect all your drives (hdd/dvd/floppy) then boot from usb, you should get to the C:\>

onyxx wrote:Just disconnect all your drives (hdd/dvd/floppy) then boot from usb, you should get to the C:\>

hi - just tried that didnt work....disconnected all the power cables from all the drives....went to boot menu selected boot from usb flash drive..see pic first


pressed enter...gave the following error see pic...


looks like ill have to go with the jungleflasher way...damm, after all this reading up on the tut and the help you guys have given me...please help...ta

Looks like it's not seeing the boot record on the jump drive. You may have to go into your BIOS settings and look around to see if you can find anything thats related to booting off a USB device. Each BIOS is different so we won't be able to tell you much about what settings to look for.

You might even try a floppy disk if you have one.

sadalius wrote:Looks like it's not seeing the boot record on the jump drive. You may have to go into your BIOS settings and look around to see if you can find anything thats related to booting off a USB device. Each BIOS is different so we won't be able to tell you much about what settings to look for.

You might even try a floppy disk if you have one.

i thought id just see if i could boot this usb flash drive on my laptop, just to see if it does....selected "boot from usb drive" in bios boot options....and it WORKED !.....but thats no ggod to me as its on my laptop...looks like my pc doesnt support usb bootup.....how do i use a floppy ?..ive got a disk and a toshiba usb floppy ....

use iprep to set it up. Just choose the A: drive for your target. Then set your BIOS boot order to A: first boot device. When you set it up, you'll only want to select the firmware for the drive that you are working with, like if your doing a lite-on only load up the lite-on firmware and don't worry about the samsung or the benq firmware. If you load all three firmwares, you'll get a insufficient disk space message when you try and read out the firmware.

sadalius wrote:use iprep to set it up. Just choose the A: drive for your target. Then set your BIOS boot order to A: first boot device. When you set it up, you'll only want to select the firmware for the drive that you are working with, like if your doing a lite-on only load up the lite-on firmware and don't worry about the samsung or the benq firmware. If you load all three firmwares, you'll get a insufficient disk space message when you try and read out the firmware.

..how will i save my key, enquiry and identify files ?......will they be on the floppy drive A ?....will everything be as the video tut ?

Your only changing the boot media. Everything else will be the same. The only difference is you would be using a floppy instead of a jump drive.

sadalius wrote:Your only changing the boot media. Everything else will be the same. The only difference is you would be using a floppy instead of a jump drive.

thanks mate...ill try this floppy method when i can dig out my old toshiba usb floppy drive....never thought id be using a floppy....lol ......good job i kept it......ill keep you posted on how i get on...once again id like to thank eveyone who has helped me so far...appreciate it....and the replies came quick as well, keep up the good work

yeah, keep us updated man. We'll help you every bit we can.